12pc Inline Fuse Holder Set

Fuse Puller and Tester
with 2 x LR41 Batteries

50 Fast Splice Connector Set
25 Blue 14 - 18 AWG
25 Red 18 - 22 AWG
Quickly splices wires without stripping first.

36pc Butt Connector Set
Tinned Copper Connectors with Waterproof Heat Shrink Sleeves
10 - 12AWG | 14 - 16AWG | 16 - 22AWG

76pc Spade Terminal Set
Various Ring and Spade Terminals with Butt Connectors

100pc Cable Connector Set
Includes Ring / Fork / Butt / Male & Female Crimps.
Ideal for Automotive and Home use.

480pc Crimp Terminal Set
Ring : M4 | M5 | M6 | M8
Bullet Male / Female
Spade 250 Male / Female - Semi-insulated / Fully Insulated
Butt Splice
Piggy back

180pc Heat Shrink Sleeve Set
Water Resistant Insulation for Electrical Connections
Ideal for Automotive use
Sizes. 2. 3.5. 5. 7. 8. 9mm

127pc Heat Shrink Sleeve Set
40mm Long : 2.0 | 2.5 | 3.5 | 5.0
80mm Long : 7.0 | 10.0 | 13.0

24pc Electrical Clip Set
Repair broken leads on test equipment and chargers
Alligator Clips - 38. 50mm
Charging Clips - 10. 25. 30 amp

Cable Housing Removal Pliers
For Cable Housing disconnection where access is restricted.

Bulb Removal Pliers
Suitable for all types of bulbs -
Bayonet / Screw and Wedge type also heated bulbs.
Gently and firmly grips glass shell of bulb.
For removing miniature style bulbs fitted to most vehicles.
Cup-type grip bulbs a

8in. Electrical Connector Pliers
for Push Tab Style Plugs
For removing locking push tab style electrical connectors -
found on mass air flow sensors, fuel injectors and ignition coils.
Hook to pull out tab / unlock and point to engage the tab.
Separates the connector from the sensor without damage.
One hand operation to work on sensors in tight spots.

220mm Automotive Relay Pliers
To release and refit vehicle electrical relays.
With thin tips and offset handles
for easier access than traditional pliers.
Forged metal handles and PVC dipped grips.
Essential for vehicle technicians and mechanics.

Automotive Relay Removal Pliers
For the safe removal of vehicle relays in difficult areas.
Suitable for most makes and models of vehicles.

23pc Terminal Tool Kit
For the Removal of Wires from Terminal Blocks without Damage
with Various Cable Extractor Tools covering most makes of vehicles

5pc Wire Installation Kit
For the placement and extraction of cables and components.
Also safe prying open control panels / inspection covers
and plastic case assemblies.
Material : Glass-filled Nylon.
Not Suitable for High Voltage Use

5pc Wire Loom Threading Kit
For most automotive wiring tasks.
Spring Steel ideal for navigating though harness junctions.
Thread wire into populated looms.
Insert wire through grommet holes.
Pull wired groups though a vacant loom.

1012pc Terminal Set & Organiser
With a wide variety of clips / ties / terminals and connectors.
Plastic storage cabinet with 25 drawers and 50 dividers.
Dimensions : 295mm L x 225mm H x 123mm D
With - Butt Connectors
Female / Male Disconnect Insulated
Ring Terminals Insulated and Non-Insulated
Spade Terminals Insulated and Non-Insulated
Closed End and Snap Splice Connectors
Alligator Clip / Cable Tie

Connector Removal Tool for VAG / Porsche Vehicles
For safe and proper removing of most push & pull connectors
e.g. electrical connector on mass air flow sensor / MAF, pressure sensor / MAP,
ignition coil pack, headlight, fog light, level sensor, etc.
Can be used for following car types :
VW / Audi / Skoda / Seat / Porsche