7mm Hex Key / Hexagonal Wrench
Suitable for Disc Brake Servicing
Gearbox Drain Plugs and Valve Adjustment

2pc Hex Bit Set with 3/8in.Dr Sockets
7mm - 36 mm Long
9mm - 92 mm Long
For BMW and Mercedes Brake Linings on
BMW | Ford | Mazda | Mercedes | VAG

7pc 3/8in.Dr Hex Bit Set
Sizes : 3 | 4 | 5 | 6 | 7 | 8 | 10mm
110mm Long with Ball End
Suitable for Automotive use -
Headlight Alignment.
Cylinder Head Removal.
Brake Servicing
Airbag Release etc

2pc Hex Bit Set - 7mm and 8mm 3/8in.Dr
for brake Caliper removal
Total length : 24mm
Ideal where space is restricted
Applicable to Audi / Mercedes vehicles

4pc Star Bit Set - 3/8in.Dr
Sizes : T40 | T45 | T47 | T50
100mm Deep
Suitable for Cylinder Head Bolts
Brake Caliper Bolts
Accessory Fixings and CV Joint Bolts.

7pc 3/8in.Dr Spline Bit Set
Sizes : M4 | M5 | M6 | M7 | M8 | M9 | M10
110mm Long Suitable for
Gearboxes / Suspension and Back Axles
also Headlight Alignment.
Cylinder Head Removal.
Brake Servicing
Airbag Release etc.

9pc Brake Caliper Service Set
Hex Bits 3/8in.Dr : 1/4 | 3/8in. and 7 | 8 | 10mm
Star Bits 3/8in.Dr : T40 | T45 | T50
Star Bit 1/2in.Dr : T60
with Socket Rail

10pc Socket Set - 1/2in.Dr
For special automotive applications -
With 3 | 6 and 10 Point Sockets and
10mm | 12.5mm | 14mm | 19mm Pentagon Sockets

8mm - Ratchet Flare Nut Wrench
with standard Open Jaw
Chrome Vanadium

9mm - Ratchet Flare Nut Wrench
with standard Open Jaw
Chrome Vanadium

10mm - Ratchet Flare Nut Wrench
with standard Open Jaw
Chrome Vanadium

11mm - Ratchet Flare Nut Wrench
with standard Open Jaw
Chrome Vanadium

12mm - Ratchet Flare Nut Wrench
with standard Open Jaw
Chrome Vanadium

13mm - Ratchet Flare Nut Wrench
with standard Open Jaw
Chrome Vanadium

14mm - Ratchet Flare Nut Wrench
with standard Open Jaw
Chrome Vanadium

15mm - Ratchet Flare Nut Wrench
with standard Open Jaw
Chrome Vanadium

16mm - Ratchet Flare Nut Wrench
with standard Open Jaw
Chrome Vanadium

17mm - Ratchet Flare Nut Wrench
with standard Open Jaw
Chrome Vanadium

18mm - Ratchet Flare Nut Wrench
with standard Open Jaw
Chrome Vanadium

19mm - Ratchet Flare Nut Wrench
with standard Open Jaw
Chrome Vanadium

Special Brake Line Spanner
Dual Size : 10 / 11mm x 180 mm Long
Used for replacing brake pipe.
With flange to hold nut completely and prevent slipping.
Offset to aid access for flush fastener turning.

Special Brake Line Spanner
Dual Size : 12 / 14mm x 180 mm Long
Used for replacing brake pipe.
With flange to hold nut completely and prevent slipping.
Offset to aid access for flush fastener turning.

Special Brake Line Spanner
Dual Size : 14 / 17mm x 180 mm Long
Used for replacing brake pipe.
With flange to hold nut completely and prevent slipping.
Offset to aid access for flush fastener turning.

Flare Nut Spanner
Sizes : 24mm / 32mm

2pc Flare Nut Spanner Set
Sizes : 8 x 10mm | 9 x 11mm
for Thermocouples

6pc Flare Nut Spanner Set - SAE
Sizes : 1/4 | 5/16 | 3/8 | 7/16 | 1/2 9/16 | 5/8 | 11/16 | 3/4 | 13/16 | 7/8 | 1in.
15 degree offset for easy access
Ideal for fuel brake and air conditioning lines

6pc Flare Nut Spanner Set
Sizes : 6 | 8 | 10 | 12 | 13 | 14 | 15 | 17 | 19 | 21 | 22 | 24mm
15 degree offset for easy access
Ideal for fuel brake and air conditioning lines.

7pc Flare Nut Spanner Set
Sizes : 8 | 9 | 10 | 11 | 12 | 13 | 14 | 15 | 16 | 17 | 19 | 21 | 22 | 24mm
with Wallet
15 degree offset for easy access
Ideal for fuel brake and air conditioning lines.

E18 Star Slogging Wrench
with 2 striking faces.
Central 20mm / 3/4in. Square Drive
For E-type fixings on commercial brake Calipers
found on front and trailing axles.
This wrench allows assembly and disassembly of the brake Calipers
without removing the steering tie rod.

E20 Star Slogging Wrench
with 2 striking faces.
Central 20mm / 3/4in. Square Drive
For E-type fixings on commercial brake Calipers
found on front and trailing axles.
This wrench allows assembly and disassembly of the brake Calipers
without removing the steering tie rod.

E24 Star Slogging Wrench
with 2 striking faces.
Central 20mm / 3/4in. Square Drive
For E-type fixings on commercial brake Calipers
found on front and trailing axles.
This wrench allows assembly and disassembly of the brake Calipers
without removing the steering tie rod.

M24 Slogging Wrench
12-point with 2 striking faces.
Central 20mm / 3/4in. Square Drive
For commercial brake Calipers on front and trailing axles.
This wrench allows assembly and disassembly of the brake Calipers
without removing the steering tie rod.

M26 Slogging Wrench
12-point with 2 striking faces.
Central 20mm / 3/4in. Square Drive
For commercial brake Calipers on front and trailing axles.
This wrench allows assembly and disassembly of the brake Calipers
without removing the steering tie rod.

8pc Adjustable Hook & Pin Spanner Wrench Set
Jaw Range : 35 - 60 | 60 - 90 | 90 - 120mm
With interchangeable Hooks and Pin Lugs
Suitable for DIN 1804 and DIN 981 bearing nuts
For use on motorcycle suspension slotted retaining rings and
ideal for automotive / industrial / plumbing and hardware applications.
With 2 spare pins.

Accelerator / Brake Pedal Adjuster
Sets engine speed to check emissions.
Ideal for MOT check
Length : 710mm

2pc Brake Caliper Seal Groove Cleaner Set
200mm Long with different heads
For removing dirt and debris from seal ring grooves.

2pc Scraper Set
with Black electroplated shafts and Tungsten Carbide Tips
Blade Width : 16mm | 32mm. Handle : 150mm
For use on brake Calipers and back plate sliding faces,
exhaust manifolds, cylinder heads, gaskets
or any area to remove corrosion and debris.
Double edged tungsten carbide tipped blades,
remain very sharp and are precision ground.

135pc Brake Pipe Nut Set
Short Female Brake Nut : M10 x 1.0
Short Female Brake Nut : 3/8in. UNF
Short Male Brake Nut : M10 x 1.0 x L17mm
Full Thread Male Brake Nut : M10 x 1.0 x L16mm
Long Male Brake Nut : M10 x 1.0 x L20mm
Long Male Brake Nut : 3/8in. UNF x L20mm
For use with 3/16in. Pipe Metric and UNF sizes.

Brake Booster Shaft Release Tool for VAG
For separating the brake serve push rod from the brake pedal.
Applicable to Audi / Seat / Skoda / Volkswagen vehicles
Also Volkswagen Passat / 2015 - 2016 and Phaeton.
OEM Codes : T10159A | T10159B

Brake Booster Shaft Release Tool for VAG
For separating the brake serve push rod from the brake pedal.
Applicable to Audi / Volkswagen Vehicles
Audi A4
VW Bora / 1998 - 2008
VW Beetle etc.
OEM Code : T10006A

Brake Booster Shaft Release Tool for VAG
For separating the brake serve push rod from the brake pedal.
Applicable to Audi Q5 - 2009 and onwards.
OEM Code : T40136.

Brake Booster Shaft Release Tool for VAG
For separating the brake serve push rod from the brake pedal.
Applicable to Porsche Cayenne / VW Touareg - 2003 and onwards.
OEM Code : T10189.

Brake Fluid Tester
For accurately checking the quality of brake fluid.
With 5 LED?s to indicate percentage of water in the brake fluid.
Requires LR03 AAA 1.5V Battery / not included.
Automatic Power Off.

3pc Fluid Lock Set
Size range : 4.2mm - 10mm.
Three anodised aluminium bodies with composite screw.
For Clamping and sealing metal flared pipes on braking systems
also cooling system bypass / fuel pipes and AC pipes etc.
Provides an effective seal to metal brake pipes when the braking system has been opened.
Size range : 4.2mm - 10mm.
Prevents brake fluid loss and contamination of the work area.

6pc Brake Bleed Wrench Set
Sizes : 7 | 8 | 9 | 10 | 11 | 12mm - 12 point
Combined Wrench / Socket and Nipple Connector.
Ideal for bleeding brake and hydraulic clutch systems without removing the wheels.
1.2M silicon hose with check valve for safety operating.
For universal bleeder nipples.

Brake Bleed Catch Bottle Kit
Simple to use.
Everything needed to quickly bleed brakes with no mess.
Plastic bottle collects discharged fluid.
Three separate adapters fit the common bleeder screws.

Brake Bleeder Kit
With 3 Adaptors and Hoses
with Magnetic Pad for securing Bottle while in use

1L Brake Fluid Bleed Bottle
With holding chain and hook.
Variable length bleeding hose.
Bleeding nipple adaptor.

Professional Brake Bleeder
1 litre Capacity
with 1/4in Air Fitting
Air Pressure : 90 - 120psi

Brake Fluid Bleed System
with PCL Air Fitting
Working Pressure : 6 - 12 Bar
Suitable for one-man operation anf clutch systems

Brake Fluid Bleed Kit
with fluid supply bottle.
Uses workshop air supply 90 to 120psi.
Quick clean and efficient operation
without specialized brake reservoir caps.
Draws the brake fluid from brake nozzle.
Flexible rubber joint for fluid extractions.

2pc Pneumatic Brake Extractor / Refill Kit
Kit contains a vacuum fluid extractor, bleeding hose
and automatic refill bottle with New safety design.
Automatic shut off when the tank is full.
Working pressure : 70 -170psi
Air inlet : 1/4in.
Tank Capacity : 2.0L
Bottle Capacity : 1.0L
Air consumption : 5 cfm

Brake or Clutch Bleeding System
Suitable for use with ABS systems.
One-man bleeding system requiring no external power source.
2.5 litre tank allows flushing the entire system
with one fill without the risk of running the reservoir dry.
42mm diameter cap suitable for most European vehicles.
Working Pressure : 2 Bar / 30psi
Max. Pressure : 5 Bar / 70psi
NOW with 1 litre Suction Tank.

Brake Fluid Bleeder
with 4 Litre and 1 Litre suction containers.
For quick and easy extraction without a second person.
Venting requires no external power source.
Easy filling and cleaning.
With E20 adaptor suitable for European vehicles.
Working pressure : 30psi

Vacuum / Pressure Pump and Brake Bleeding Kit - 21pc
Checks vacuum and pressure operated automotive components
Can be used to bleed hydraulic systems or siphon fluids

Electric Brake Fluid Bleeder
For most makes and models of vehicles
With Adjustable pulse oil change which can effectively
clean the pipeline and change the oil more thoroughly.
Contents : Brake Fluid Bleeder / 2L Bottle & 3.5M Hose / 3 Adaptors.
Power supply : 240V | 50 / 60Hz | 35W
Output Pressure : 0.6 - 3.0 Bar
Output flow : <= 1.2L / Min
Noise Level : 70 Db
Device shuts off when container is empty

Brake and Clutch Master Cylinder Pressure Test Kit
Adaptors install directly into master cylinder access holes
Measures pressure at front or back of master cylinder
Pressure gauge 0 - 300 psi and is accurate to 4% of scale
JIC quick disconnect for easy connection

Hand Held Vacuum Pump
Test Automotive Systems
Works on all vehicle makes and models
Pump with Vacuum Gauge / Tubing and Vacuum Adaptors
Brake Fluid Reservoir

Brake Bleeder Cap - Tesla Model 3 or Y
Made of Aluminium
for power brake bleeding on Tesla Model 3 and Y vehicles.
Adaptor rotates 360 degrees.
Pressure up to 2.5bar / 36psi.
Compatible with most brake pressure bleeding machines or tank pumps.

Brake Bleeder Cap - Tesla Model S or X
Made of Aluminium
for power brake bleeding on Tesla Model 3 and Y vehicles.
Adaptor rotates 360 degrees.
Pressure up to 2.5bar / 36psi.
Compatible with most brake pressure bleeding machines or tank pumps.

Brake Bleeder Cap - Hyundai
90 degrees angled adaptor for restricted areas.
Suitable for Hyundai / Mitsubishi and Nissan.

Universal Brake Bleeding Adaptor
with Adjustable Range : 28 - 70mm.
Suitable for all vehicles with a
collar on the filler cap of the brake fluid reservoir.
Holds pressure up to 3.5bar / 50psi.

Brake Cylinder Adaptor Kit
Adapters for Domestic and Import Vehicles.
Suitable for use with most Pressure Brake Bleeders.
Contains universal adapters for most makes and models.
Adapters fit 90% of current master cylinder reservoirs.

Pneumatic Brake Pressure Bleed Kit
Low pressure tank 10 - 40psi which can be pre-charged
with compressed air - making the unit fully portable.
Suitable for use on ABS systems.
Supplied with a range of vehicle adaptors.

Brake Pressure Test Kit
With Teves Adapter
Swivel Fittings | Straight Fittings
M10-1.0 Bleeder Adapter
2 - 325 Mpa Gauge Assembly

Brake Caliper File - 150mm Blade

Brake Cylinder Hone
20 - 64mm | 3/4 to 2-1/2in. diameter
Flexible shaft for ease of use and self centring.

Replacement Abrasive Stones
30mm | 1-1/8in. | 220 Grit
for CT2756 Cylinder Hone

Cylinder Hone
with 75mm / 3in. Abrasive Stones
Range : 51 - 177mm / 2 to 7in. Bore Diameter
Flexible shaft for ease of use and self centring

Replacement Abrasive Stones
75mm / 3in.
for CT2757 Cylinder Hone

Cylinder Hone
with 100mm / 4in. Abrasive Stones
Range : 50 - 180mm / 2 to 7in. Bore Diameter
Flexible shaft for ease of use and self centring

Replacement Abrasive Stones
100mm | 4in. | 220 Grit
for CT2757 Cylinder Hone

3pc Brake Adaptor Set
2 pin and 3 pin adjustable brake Caliper rewind adaptors.
Magnetic 2 Pin 3/8in.Drive adaptor.
2 Pin Adaptor fits most vehicles.
3 Pin Adaptor for Electronic Park Brake / EPB tools.

2 & 3 Pin Brake Piston Reset Adaptor Set
3/8in.Dr | Range : 20mm - 35mm with adjustable Pins.
For resetting the brake pistons with 2 / 3 or 4 grooves.
Universal - suitable for a variety of vehicle models.
Use a ratchet for easy rewinding of the Caliper piston.
Covers a range of vehicles including Electronic Park Brake models.

Disc Brake Piston Rewind Tool
3/8in.Dr Forcing Screw with Left Hand Thread and Reaction Plate
Reversible Keys : 22mm | 32mm
For use on disc brake Calipers fitted to most vehicles

Disc Brake Piston Rewind Tool
Right Hand Thread with Reaction Plate and Reversible Key
3/8in.Dr
For use on disc brake Calipers fitted to most vehicles

2 in 1 Brake Piston Rewind Tool Set
For use on disc brakes fitted to most cars.
Complete with 3/8in. square drive Reversible Adaptors.
With 22mm and 32mm Pins
Enables retraction of piston into the bore allowing new brake pads to be installed.
With Hex handle for use with a socket or spanner for extra torque.
Right handed thread brake Caliper rewind tool.

Disc Brake Piston Rewind Tool
For Citroen / Peugeot and Renault Vehicles
Adaptor 2 - Citroen XM XMT Turbo CT. 2.0 XANTIA1.8 1.9D/DT. 2.0I 2.0 1.65
Adaptor Z - Renault Laguna 2.0 ABS / 2.2 / Saferane2.0 2.2 TD

Disc Brake Piston Rewind Tool
Right and Left Thread in One Tool
3/8in.Dr Force Screw with Reaction Plate
3/8in.Dr Adaptor

5pc Brake Caliper Piston Rewind Kit - 3/8in.Dr
With powerful internal spring
T-Bar : 150mm | Main Body : 110mm plus Reaction Plate.
Magnetic 2 pin adaptor with 5mm diameter pins - for any standard rewind adaptor.
Adjustable 2 pin adaptor with 3mm diameter pins
from 25mm to 34mm pin centres - for electronic park brakes.
Adjustable 3 pin adaptor with 3mm diameter pins
from 17mm to 30mm pin centres - for common brake Caliper applications.

Disc Brake Piston Rewind Set
For Push-back and Wind-back disc brake Pistons
For brake pad replacement and Caliper servicing on collette type brakes

7pc Disc Brake Piston Rewind Tool Kit
Adjustable 2 pin adaptor fits most vehicles.
Adjustable 3 pin adaptor only to be used with
Electronic Park Brake / EPB tools.
Applicable to : Audi | B29 | BMW | Iveco Daily |
Renault | Range Rover | Seat | VW | Volvo

7pc Brake Caliper Rewind Tool Kit
For resetting brake pistons on Iveco Truck disc brakes
Suitable for Iveco Stralis / Euro cargo / Daily
With : 10mm Ratchet Wrench
Magnetic Rewind Tool with Backing Plate
Reset Discs with 2 and 3 pins
8mm Hex Bits with 10mm drive
NOTE : 2 Pin Reset Disc is 3/8in.Dr

18pc Disc Brake Piston Rewind Set
With Right and Left threaded Spindles
For Pads on both Wind Back and Push Back Type Brakes
Suitable for most makes and models.

Disc Brake Piston Caliper Rewind Set
Left and Right Hand Thread
24 Adaptors and Caliper Keys
6 and 7mm Hex Keys
3 and 5mm Pin Punches
4 Special Reaction Plates

Disc Brake Caliper Piston Rewind Set
Air Powered Wind Back Tool 80-100psi
Compatible with 3/8in.Dr tools
Right and Left hand Operation
Converter for 2 pin Adaptors
15 Wind Back Keys

Air Disc Brake Piston Rewind Tool
For servicing / replacement of worn brake disc pads
Suitable for push back and wind back brake Pistons
Compatible with 3/8in.Dr adaptors

Disc Brake Piston Compressor
Special wide compressor for 4 Piston Calipers.
Jaw width - 88mm
Applicable to -
BMW and Mercedes Benz with
the 4 Piston Disc Brake models

87mm Disc Brake Pad Spreader
Use with 1/2in.Dr Ratchet or 21mm Spanner.
Suitable for ATE / Bendix / Delco and Girling Calipers.
Standard and 4-Piston Disc Brakes.

Ratchet Type Brake Caliper Press
Evenly spreads force in a parallel manner
to prevent misalignment of Pistons.
Allows work on 2 and 4 Piston fixed Calipers
as well as single and twin Piston floating Calipers.

Disc Brake Pad Spreader
Suitable for ATE / Bendix / Delco and Girling Calipers.
Standard and 4-Piston Disc Brakes.

Disc Brake Pad Puller
For the quick removal of disc brake pads.
Especially useful where brakes have seized.
Mini slide hammer to ease pad from Caliper

Disc Brake Pad Spreader with Twin Bolts
Used to compress Pistons back into Calipers
when installing new brake pads on any single or dual sliding type Caliper
Swivelling nose pieces reduce the chance of Piston cocking
Fine threaded screws for added pressure

Hydraulic Brake Hose Clamp
One-handed snap action Clamp for Brake hydraulic hoses.
Dimensions : 210 x 40 x 10mm

2pc Brake Line Jig Set
Clamp both new and old lines parallel
to each other to make exact copies.
A brake line can consist of many angles /
bends that should be correct for the new line to fit.
For steel / cooper and plastic coated brake lines
with 3/16in. or 1/4in.| 4.75mm to 6.3mm diameters.

Brake Pipe Bender
for 3. 4. 6mm diameter Tubing

Brake Pipe Bending Tool
for bending 5mm diameter brake lines.
With 2 bending options - Tight and Open radius bends.
Central 6mm Hex slot

Brake Pipe Bending Pliers
Special shaped jaws.
Bend 3/16in. and 1/4in. brake and fuel lines.
Forged steel.
Cushioned grips.
Bends without distortion.

Universal Bending Tool
Forms wire and flat metal
into Clamps / handles / brackets / hooks and coils.
Easily attaches to work bench or vice to make angle bends up to
5/16in. / 8mm diameter Rod and
1-3/16 x 1/12in. / 30 x 2mm Flat Metal.

Mercedes Brake Spring Installer
Unique tool for Mercedes vehicle parking brake.
For disassembly and assembly of spring clips on rear disk brakes
Length : 132mm

Handbrake Shoe Retaining Spring Tool
with 2mm wide guide slot.
for Mercedes-Benz V-Class Vehicles.
Enables access to the retaining clips behind the rear drive flange.
For easy removal and fitting of the shoe retaining clips
on the handbrake shoes.
Applicable to : Vito / Vitano -
Typ 638 / 1996 - 2003
Typ 639 / 2003 - 2014
Typ 447 / from 2014

Brake Spring Pliers
220mm long
For the removal of drum brake return springs.
One end grips on the brake lining the other hooks onto the spring.
Suitable for most vehicle drum brakes.

153mm T-Handle Assembly Hook
For Brake Springs and also Headlight units

4pc HGV Brake Caliper Socket Set
Hex 8mm | 10mm | S8 and 11PT
12mm Hex Drive
for Commercial SAF / NFZ / Knorr brake Caliper systems

Brake Caliper Socket
11pt Spline | 3/8in.Dr | 26mm Deep
For Knorr-Bremse Brake Calipers on Volvo trucks also
DAF / Foden / MAN / Mercedes / Scania / BOVA
plus BPW & SAF Trailers.

17pc Brake Caliper Socket and Bit Set
Impact Hex Bits : 7 | 8 | 9 | 11mm
Special Brake Caliper Sockets : 11.5 | 14 | 15 | 20 | 22mm
Pentagon Sockets : 10 | 12.5 | 14 | 19mm
Pentagon Bit :10mm
For use on brake Calipers when replacing the brake pads.
Applicable to : Alfa Romeo / Audi / BMW / Ford / Mercedes / Porsche.

3pc 1/2in.Dr Socket and Bit Set Brake Servicing Kit
Pentagon Profile

8pc Brake Caliper Bleed Nipple Repair Kit
Suitable for repairing Brake Caliper Bleed Nipples : M5 to M8.
Contents :
Drill : 8.5mm
Tap : 1/8in. - BSP28
6 Bleed Nipple Inserts : 1/8in.- BSP28 x 30mm

8pc Brake Caliper Bleed Nipple Repair Kit
Suitable for repairing Brake Caliper Bleed Nipples : M8 to M10.
Contents :
Drill : 10mm
Tap : M11.5 x 1.0mm
6 Bleed Nipple Inserts : M11.5 x 36mm

12pc Brake Caliper Guide Bolt Thread Repair Set
Used for repairing faulty inner threads on
brake Caliper guide bolts in wheel bearing
housing brake Caliper carriers with NO
need to remove the wheel bearings or struts.
For use on most Ford -
Vauxhall / Opel - Vauxhall | Opel and
VAG - Audi | Seat | Skoda | VW vehicles.

15pc Brake Caliper Thread Repair Set
For rethreading brake Caliper bolt holes.
With Step drill to increase hole sizes.
M12 x 1.5mm tap step drill insert locator.
Washers with centre roller bearing.
10 replacement inserts.

16pc Brake Caliper Guide Thread Repair Kit
with Titanium coated core drill
Tap and 10 threaded inserts.
Applicable to
Volkswagen - Golf MKIV / Beetle
Seat - Exeo Estate ST 170
Ford - Focus | C-Max
Vauxhall - Astra-G

5pc ABS Sensor Reamer Set - 1/4in.Dr
1/4in.Dr. / 125mm long T-Bar Handle.
4 popular sized reamers for removing dirt / dust and rust.
Sizes : 14 x 32mm | 15 x 23mm | 18 x 23mm | 18 x 34mm.
Applicable to most makes and models of vehicles.
BMW / Fiat Group / Ford / Mercedes / PSA / VAG.

5pc Elbow Connector Socket Set
Sizes : 12 | 14 | 17 | 19 | 22mm
3/8in.Dr / Single Hex and 50mm Deep
Chrome Vanadium
Suitable for L-type pipe fittings on trucks.
Suitable for construction equipment and general machinery.

Manual Tube Expander
7-in-1 Pipe Expander for copper and aluminium tubing.
Sizes : 6 | 8 | 10 | 12 | 16 | 19 | 22mm
1/4 | 5/16 | 3/8 | 1/2 | 5/8 | 3/4 | 7/8in.
Made of heavy duty alloy steel for a long working life.

Universal Flaring Too Kit
Adjustable | 5 - 16mm
For creating conical / tapered flares.
For Brass or Aluminium pipes.
Size range : 5 - 16mm | 3/16 - 5/8in.

Micro Brake Pipe Flaring Tool - 3/16in. SAE
For Copper / Cupronickel and Steel Pipes.
Hand-held brake pipe flaring tool that is capable of forming both
SAE single and double flares in 3/16in. / 4.75mm diameter pipes.
The compact design makes it ideal for on vehicle use and
allows for it to fit in an engine bay or under a wheel arch
when replacing or repairing a brake pipe.
High-pressure punch grease also included to lubricate friction surfaces.

6pc Pipe Flaring Kit
Steel Compressor Yoke : 3/16 | 1/4 | 5/16 | 3/8 | 1/2 | 5/8in.
Flaring Tool
Flexible Tube Benders
Tube Cutter 3 - 28mm

6pc Brake Pipe Flaring Kit
With Quick Release Dies
Brake Flaring Tool Suitable For 3/16in. or 4.75mm Diameter Tubing
Secure Clamping with Quick Release.

7pc Flaring Tool Set
For Single or Double Flaring Aluminium and copper tubing
Adaptors for 3/16 | 1/4 | 5/16 | 3/8 | 1/2in. Tube or 4.8 - 12.7mm

10pc Pipe Flaring Kit
Steel Compressor Yoke
Flaring Tool
Flaring Dies - 5. 6. 8. 10. 12. 14. 16mm

Copper Tube Flaring Tool Kit
Imperial : 1/4 | 5/16 | 3/8 | 1/2 | 5/8 | 3/4in.
Metric : 6 | 8 | 10 | 12 | 16 | 19mm
Suitable for soft copper, aluminium, brass and other soft metals.
Allows easy and smooth operation saving time and energy.
Off-centre mounted cone spins on an axis for a uniform shape.
Arc frame ergonomic yoke designed with double ring bar
guarantees a professional job with permanent levelling.
Include tools for shortening or de-burring
and 45 degree single flaring of pipes.

Professional Brake Line Flaring Tool Kit
For flaring brake pipes and hydraulic tubing.
Can be used on copper / brass / aluminium and steel pipes
For coated and non-coated pipes.
For inside and outside flaring.
Includes 4 pairs of pressure pieces :
4.75mm | 6.35mm | 8mm | 9.5mm
3/16in. | 1/4in. | 5/16in. | 3/8in.

8pc Brake Tool Set
Spring Compressor
Brake Spring Installer
Spring Removal Tool
Brake Retaining Spring Tool
Brake Spring Pliers
2 Brake Adjustment Spoons
Mini Adjustment Spoon
Popular brake tools for servicing brakes on most vehicles.

15pc Comprehensive Brake Service Tool Set
Brake Line Flare Nut Wrench
Brake Spring Pliers and Spring Tool
Pound Thru Screwdriver and Hex Socket Bits
Brake Caliper File and Brushes
Brake Cable Hook
Assembly Tool

Brake Drum Gauge
Size Range 160mm - 360mm
Metric and Imperial Scale.
Developed to measure the wear limit on brake drums
as well as the diameter of the drum and then establish
the shoe position prior to drum re-fitting.
For o

8pc Brake Gauge Set
Colour coded for ease of use
Green for Go : 8mm | 10mm | 12mm
Yellow for Caution : 4mm | 5mm | 6mm
Red for stop and replace : 2mm | 3mm

100mm Digital Brake Disc and Drum Caliper
For measuring external brake disc thickness and internal small drums.
Easy Read Digital LCD Display - 11mm high characters.
Metric or Imperial read-out with Hold function.
Range : 0 - 100mm / 0 - 4in.
Resolution : 0.01mm / 0.0005in.
Battery : SR44-1.5V - supplied.

150mm Digital Brake Disc and Drum Caliper
Measures external brake disc and internal small drums
LCD display with 11mm high figures for easy reading
Metric or Imperial read-out with Hold function
Supplied with calibration certificate and storage case
Range : 0 - 150mm / 0 - 6in.
Resolution : 0.01mm / 0.0005in.
Battery : 1.5V SR44 - supplied

3pc Brake Disc Run Out Kit
Allows the DTi gauge to be mounted in almost any position
against the brake disc to measure disc warp.
DTi Gauge accurate to 0.01mm / total deflection 10mm.
The Locking pliers allow fixing to suspension bracket or component part
Segmented Steel Mounting Post can be bent and locked into position.
Universal - measures brake disc drive flange or any rotating component run-out.
Can be used on motorcycles.

Dial Test Indicator & Precision Point Set
0 - 10mm Dial in 0.01mm increments.
Magnetic base with fine adjustment.
Magnet has a 60kg pull.
On / Off Switch for easy positioning.
Used to check variations in machined parts.
Ideal for checking run-out on disc brakes.

5pc Wheel Cylinder Cup / Seal Installation Rocket Set
Tapered Cones enable wheel cylinder o-rings and seals
to be installed easily without damage to the brake cylinder assembly.
Sizes :
1 - 3/4'' | 44.5 / 47.5mm
1 - 7/8'' | 48 / 51mm
2 - 1/8'' | 54 / 57mm
2 - 3/16'' | 56 / 59mm
2 - 5/16'' | 59 / 62mm

Universal Hub / Brake Drum Puller
Suitable for removing 4-stud vehicle wheel hubs.
Bolt centres : 100 - 115mm
Overall width : 145mm
Depth : 38mm

Motorcycle Brake Caliper Piston Remover
Range : 18mm - 30mm
Universal

Motorcycle Brake Piston Removal Tool Set
For dismantling motorcycle brakes with sliding Calipers.
Removes frozen Pistons with ease.
Includes 12 universal adaptors - 19 to 30mm.
Will not mark or damage the working part of the Piston.
Suitable for nearly all makes and models

Haldex Brake Linkage Adjuster Extractor
Allows tight brake linkage adjusters to be pulled off.
Ring shaped contact surface for a secure hold.
Hex : 32mm
Puller inside depth : 84mm
Puller inside width : 86mm
Spindle length : 9

6in. / 150mm Composite Caliper
or Vernier Gauge
Dual scale - Imperial / Metric
Measure Inner / Outer Diameter and Depth

Vernier Caliper Accessory Kit for CT2305
For extending the measurement capabilities of Calipers.
Allows for deeper measurement points
especially inwardly tapered components.
With 2 legs and 6 tips : short / long
Perfect for use on disc brakes.